Προβλημα με το κουμπι + σε control panel

Περισσότερα
4 Χρόνια 9 Μήνες πριν #168128 από hellion
Απαντήθηκε από hellion στο θέμα Προβλημα με το κουμπι + σε control panel
Το κουμπι ακουγεται και οπως ειπα το τεσταρα και κανει επαφη...γι'αυτο εχω τρομαξει και δεν ξερω τι μπορει να ειναι. Ενα κουμπι που μου ειχε χαλασει πιο παλια (το on off) το αλλαξα και ολα καλα, παντως ευχαριστω που σκεφτεστε παραλληλα με μενα για το τι μπορει να συμβαινει...

Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.

Περισσότερα
4 Χρόνια 9 Μήνες πριν #168130 από Nasikas
Απαντήθηκε από Nasikas στο θέμα Προβλημα με το κουμπι + σε control panel
Φόρουμ αλληλεγγύης είμαστε - μην το ξεχνάμε.
Αν ήσασταν κοντά μου, θα έβγαζα εύκολα το display απο ίδια σόμπα φίλου και θα δοκιμάζαμε αν λειτουργεί. Ήτοι να αποκλείσουμε την πιθανότητα ότι φταίει το σύστημα παρακάτω. (πλακέτα)
Εχει κανείς εκεί κοντά ίδια σόμπα ? Φίλος η γνωστός ?
Η έστω φορουμίτης ? - Μην διστάζετε να βοηθάτε κόσμο όταν μπορείτε.

* (στην γιορτή μου έλαβα με κούριερ ένα ζευγάρι γυαλιά ηλίου. Ήταν απο μια οικογένεια που στο χιονοδρομικό κέντρο είχε κολλήσει το τζάμι του οδηγού και δεν ανέβαινε. (Το είχαν κλείσει με σακούλα λιπάσματος, αλλά θα έβγαζαν διακοπές Χριστουγέννων με φόβο μην τους το ανοίξουν.) Εβγαλα απο ίδιο αυτοκίνητο συγγενούς μου το χειριστήριο παραθύρου - τους ανέβασα το παράθυρο - και το έβαλα ξανά στην θέση του. - - Δεν το γράφω για τα γυαλιά...ε ...Η χαρά που πήρα επειδή τους βοήθησα ήταν μεγαλύτερη)


Χαίρομαι που όλοι έγιναν ειδικοί στο πέλλετ.
Χαίρομαι που βλέπουν με δέος καθε ξενικό όνομα που κυκλοφορεί.
Επιβεβαιώνομαι.
Πάντα...

Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.

Περισσότερα
4 Χρόνια 9 Μήνες πριν #168149 από hellion
Απαντήθηκε από hellion στο θέμα Προβλημα με το κουμπι + σε control panel
Καλησπερα.
Δυστυχώς δεν γνωριζω καποιον που να εχει ιδια σομπα με εμενα (βασικα κανεναν με σομπα πελλετ) οποτε δεν μπορω να δοκιμασω αυτο που λετε. Σιγουρα το κουμπι δουλευει. Το led ομως δεν αναβει οταν το παταω οποτε αυτο δειχνει οτι δεν "φευγει" η εντολη..ετσι δεν ειναι? Αν ειχα το pinout απο το display θα μπορουσα να δω στα pin που αντιστοιχούν στο κουμπι αν γινεται κατι.... .
Κατι αλλο αν γνωριζετε... οι σομπες εχουν ολες υποστηριξη για τηλεχειρισμό η όχι; Για να αγοραζα ενα κοντρολ για να μην φθειρω τα κουμπια απο το display.
Τελος παντων, θα πραξω τα σχετικα και θα σας ενημερώσω.... ευχαριστω και παλι.

Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.

Περισσότερα
4 Χρόνια 9 Μήνες πριν - 4 Χρόνια 9 Μήνες πριν #168156 από ΚΩΣΤΑΣ ΠΗΧΑΣ
!ΤΟ συγκεκριμενο πανελ δεχεται τηλεχειρηστηριο.το θεμα ειναι οτι θα πρεπει να βγαλεις το πανελ μαζι με την καλωδιοταινια και να το πας σε καποιον με πολυμετρο να ελεξει και το κουμπι και τις γραμμες αν καταληγουν και κανουν επαφη στη φισα τις καλοδιοταινιας,ΑΛΛΙΩΣ ΚΑΙΝΟΥΡΓΙΟ Η ΤΗΛΕΧΕΙΡΗΣΤΗΡΙΟ ΜΕ ΔΟΚΙΜΗ ΑΝ ΤΑΙΡΙΑΞΕΙ!!!!!!!!!!ΜΗΝ ΠΑΙΔΕΥΕΣΑΙ ΜΟΝΟΣ ΣΟΥ ΑΝ ΔΕΝ ΚΑΤΕΧΕΙΣ
Last edit: 4 Χρόνια 9 Μήνες πριν by ΚΩΣΤΑΣ ΠΗΧΑΣ.

Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.

Περισσότερα
4 Χρόνια 9 Μήνες πριν - 4 Χρόνια 9 Μήνες πριν #168157 από ΚΩΣΤΑΣ ΠΗΧΑΣ
ΔΕΣ ΚΑΙ ΣΤΟ PDF ΑΡΧΕΙΟ www.energ.gr/index.php?option=com_kunena...1&id=60625&Itemid=74 ----11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY ΕΙΝΑΙ ΤΟ ΜΑΝΙΟΥΑΛ ΑΠΟ ΤΟ ΚΟΝΤΡΟΛΕΡ-ΠΑΝΕΛ ΕΙΝΑΙ ΣΤΑ ΑΓΓΛΙΚΑ11.1 Proper functioning and control adjustment devices
11.1.1 Control panel
The control board can be managed by simply pressing a few buttons on the control panel. A display and the LED indicators inform
about the stove operational status. When in programming mode all the parameters that can be modified using the buttons are shown
on the display.
11.1.2 LED indicators
LED Meaning when switched on
ROOM TEMP SETTING Room temperature value setting
HEAT OUTPUT SETTING Heat output value setting
CHRONO Chrono enabled
ALARM Stove in alarm
IGNITION PLUG Ignition plug switching on
AUGER TUBE ON Auger tube moving
EXCHANGER-PUMP Exchanger \ pump switched on
ON\OFF Working status
Display
display function status display shows
DISPLAY
status
heat output
parameter label
OFF OFF+ROOM TEMPERATURE
SWITCHING ON ACCENDE+ROOM TEMPERATURE
FEEDING CARICA PELLET
WORKING
ROOM TEMPERATURE+HEAT
OUTPUT+TIME
PROGRAMMING SELECTED PARAMETER
OFF
Chrono LED
Heat output setting LED
Room temperature setting LED
Status/heat output/parameter display
ON/OFF LED
P1 button decrease/
menu/room
temperature setting
P2 button increase/
stove status/heat output
setting
P3 button ON/OFF/
exit/confirm
Auger tube/ exchangerpump/
ignition plug LED
Alarm LED
48
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.2 Menu
Hold P1 button down to access the menu.
It includes several items and levels to access settings and control board programming.
11.2.1 User Menu
The table below briefly describes the menu structure, focusing in particular on the functions available to users.
level 1 level 2 level 3 value
M1 – time clock setting -
Week day M-T-W-Th-F-S-Su
Time c l oc k hour s 0-11
Time clock minutes 0-59
Time clock day 1-31
Time c lock month 1-12
Time c lock year 00-99
M2 – Chrono setting
M2-1 - enable chrono
01 – enable chrono on/off
M2-2 – daily programming
01 – day chrono on/off
02 - start 1 day OFF-0-11:50 pm
03 - stop 1 day OFF-0-11:50 pm
04 - start 2 day OFF-0-11:50 pm
05 - stop 2 day OFF-0-11:50 pm
M2-3 - weekly programming
01 - weekly programming on/off
02 - start Prog 1 OFF-0-11:50 pm
03 - stop Prog 1 OFF-0-11:50 pm
04 – Monday Prog 1 on/off
05 - Tuesday Prog 1 on/off
06 - Wednesday Prog 1 on/off
07 - Thursday Prog 1 on/off
08 - Friday Prog 1 on/off
09 - Saturday Prog 1 on/off
10 - Sunday Prog 1 on/off
11 - start Prog 2 OFF-0-11:50 pm
12 - stop Prog 2 OFF-0-11:50 pm
13 - Monday Prog 2 on/off
14 - Tuesday Prog 2 on/off
15 - Wednesday Prog 2 on/off
16 - Thursday Prog 2 on/off
17 - Friday Prog 2 on/off
18 - Saturday Prog 2 on/off
19 - Sunday Prog 2 on/off
20 - start Prog 3 OFF-0-11:50 pm
21 - stop Prog 3 OFF-0-11:50 pm
22 - Monday Prog 3 on/off
23 - Tuesday Prog 3 on/off
24 - Wednesday Prog 3 on/off
25 - Thursday Prog 3 on/off
26 - Friday Prog 3 on/off
27 - Saturday Prog 3 on/off
28 - Sunday Prog 3 on/off
29 - start Prog 4 OFF-0-11:50 pm
30 - stop Prog 4 OFF-0-11:50pm
31 - Monday Prog 4 on/off
32 - Tuesday Prog 4 on/off
33 - Wednesday Prog 4 on/off
34 - Thursday Prog 4 on/off
35 - Friday Prog 4 on/off
36 - Saturday Prog 4 on/off
37 - Sunday Prog 4 on/off
49
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.2.2 Menu M01 – time clock setting
Use this function to set current time and date. The control board is equipped with a lithium battery guaranteeing the time clock a life
longer than 3/5 years.
Hold P1 button down for 2 seconds to access the general programming menu. Press P1 (decrease) or P2 (increase) button to select M1
item. The message “M1 set orologio” will scroll on the display. (figure 13a)
Figure 13 a
Figure 13 b
M2-4 – weekend programming
01 – weekend chrono on/off
02 - start weekend 1 OFF-0-11:50 pm
03 - stop weekend 1 OFF-0-11:50pm
04 - start weekend 2 OFF-0-11:50 pm
05 - stop weekend 2 OFF-0-11:50 pm
M2-5 - exit set
M3 – select language
01 – Italian set
02 – English set
03 – French set
03 - German set
M4 - stand-by
01 - stand – by on/off
MS – Buzzer
01 – buzzer On/off
M6 – First load
01 – First load 90”
M7 – Stove status
01 – Stove status
01 – Auger tube status info
02 – T minutes info
03 – Thermostat status Info
04 – Fume status Info
05 – Exhaust blower rev. status rpm Info
M8 - Technician settings
01 - Password set
M9 - Exit
01 - Exit set
LUN
MI
50
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
Select the desired day and press P3 button (figure 13b). Then set the hour (figure 13c), minutes (figure 13d), day (figure 13e), month
(figure 13f) and year (figure 13g) by pressing P1 (decrease) and P2 (increase) buttons. Press P3 button to confirm the desired value.
ANN
MES
GIO
MIN
ORE
51
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.2.3 Menu M02 – chrono setting
Sub-menu M2 – 1 – Enable chrono
All programmable thermostat functions can be disabled and enabled by means of the menu that appears on the display "M2 set crono”
(M2 chrono set). Press P3 button and then P1 or P2, for selecting On or Off respectively, to enable the programmable thermostat.
Press P3 button to confirm. (figure 14a)
figure 14a
Sob-menu M2 - 2 – Daily programming
After selecting menu “M2-2 day programm”, press P3 button to scroll through the different programming parameters available for the
daily programmable thermostat, including the possibility of enabling it (figure 14b).
figure 14b
It is possible to set two on/off times (the first with START1 Day and STOP1 Day and the second with START2 Day and STOP2 Day)
defined by the times set according to the table below. If the value is set to OFF, the time clock ignores the control. Use P1 (decrease)
and P2 (increase) buttons to modify the value and P3 to confirm.
DAILY PROGRAMMING
Menu level setting meaning Available values
M2-2-01 DAY CHRONO Enable daily chrono ON/OFF
M2-2-02 START 1 Day Switching-on time OFF-0-11:50
M2-2-03 STOP 1 Day Switching-off time OFF-0-11:50
M2-2-04 START 2 Day Switching-on time OFF-0-11:50
M2-2-05 STOP 2 Day Switching-off time OFF-0-11:50
Sub-menu M2 - 3 – Weekly programming
The weekly programmable thermostat functions can be enabled/disabled and set using the menu “M2-3 Program Settim-” (M2-3
Week Programm). The weekly programming function features 4 independent programmes. Moreover, if the time is set to OFF, the time
clock ignores the corresponding control.
The weekly programming function is briefly described in the tables below. Press P3 to confirm the value and pass to the following
function. Hold P3 button down to exit the menu.
ENABLING WEEKLY CHRONO
menu level setting meaning available values
M2-3-01 WEEKLY CHRONO Enable weekly chrono ON/OFF
CRO
ABIL
52
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
PROGRAMME 1
menu level setting meaning available values
M2-3-02 START PRG 1 switching-on time OFF-0-11:50
M2-3-03 STOP PRG 1 switching-off time OFF-0-11:50
M2-3-04 MONDAY PRG 1 on/off
M2-3-05 TUESDAY PRG 1 on/off
M2-3-06 WEDNESDAY PRG 1 on/off
M2-3-07 THURSDAY PRG 1 on/off
M2-3-08 FRIDAY PRG 1 on/off
M2-3-09 SATURDAY PRG 1 on/off
M2-3-10 SUNDAY PROG 1 on/off
PROGRAMME 2
menu level setting meaning available values
M2-3-1 1 START PRG 2 switching-on time OFF-0-11:50
M2-3-12 STOP PRG 2 switching-off time OFF-0-11:50
M2-3-13 MONDAY PRG 2 on/off
M2-3-14 TUESDAY PRG 2 on/off
M2-3-15 WEDNESDAY PRG 2 on/off
M2-3-16 THURSDAY PRG 2 on/off
M2-3-17 FRIDAY PRG 2 on/off
M2-3-18 SATURDAY PRG 2 on/off
M2-3-19 SUNDAY PROG 2 on/off
PROGRAMME 3
menu level setting meaning available values
M2-3-20 START PRG 3 switching-on time OFF-0-11:50
M2-3-21 STOP PRG 3 switching-off time OFF-0-11:50
M2-3-22 MONDAY PRG 3 on/off
M2-3-23 TUESDAY PRG 3 on/off
M2-3-24 WEDNESDAY PRG 3 on/off
M2-3-25 THURSDAY PRG 3 on/off
M2-3-26 FRIDAY PRG 3 on/off
M2-3-27 SATURDAY PRG 3 on/off
M2-3-28 SUNDAY PROG 3 on/off
PROGRAMME 4
menu level setting meaning available values
M2-3-29 START PRG 4 switching-on time OFF-0-11:50
M2-3-30 STOP PRG 4 switching-off time OFF-0-11:50
M2-3-31 MONDAY PRG 4 on/off
M2-3-32 TUESDAY PRG 4 on/off
M2-3-33 WEDNESDAY PRG 4 on/off
M2-3-34 THURSDAY PRG 4 on/off
M2-3-35 FRIDAY PRG 4 on/off
M2-3-36 SATURDAY PRG 4 on/off
M2-3-37 SUNDAY PROG 4 on/off
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
53
Sub-menu M2 - 4 – weekend programming
The programmable thermostat functions can be enabled/disabled and set for the weekend (days 6 and 7, or Saturday and Sunday). Select
“crono fine-sett” (weekend chrono) item and press P3 button to enable it. Then select “on” using P1 (decrease) or P2 (increase) button. Set
Start 1 fine - sett (Start 1 weekend)and Stop 1 fine – sett (Stop 1 weekend) times to define the stove operating period concerning
Saturday and (Start 2 weekend) and (Stop 2 weekend) times to define the stove operating period concerning Sunday.
WEEKEND PROGRAMMING
menu level setting meaning available values
M2-4-01 WEEKEND CHRONO Enable weekend chrono ON/OFF
M2-4-02 START 1 WEEKEND switching-on time OFF-0-11:50
M2-4-03 STOP 1 WEEKEND switching-off time OFF-0-11:50
M2-4-04 START 2 WEEKEND switching-on time OFF-0-11:50
M2-4-05 STOP 2 WEEKEND switching-off time OFF-0-11:50
11.2.4 Menu M03 – select language
Use this function to select one of the languages available (figure 15). Press P2 (increase) and P1 (decrease) buttons to scroll through
the options and press P3 button to confirm.
figure 15
11.2.5 Menu M04 – stand-by
Use this function to enable or disable the Stand-by mode (figure 16). Press P3 button to select menu M4 and then P1 (decrease) or
P2 (increase) button to select the ON or OFF status. Refer to the section concerning the stand-by mode for more details on its
functioning.
figure 16
11.2.6 Menu M05 – buzzer mode
Use this function to enable or disable the control board buzzer during alarms (figure 17). Press P1 or P2 button to enable or disable this
function and P3 button to confirm.
figure 17
CIC
STA
LIN
54
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.2.7 Menu M06 – first load
This function is available only when the stove is switched OFF. It allows the Auger tube to be loaded upon the first stove start-up when the
pellet hopper is empty. After selecting menu M6, the message "Premere più" (figure 18a) will scroll on the display. Then press P2
(increase). The exhaust blower switches on at the maximum speed and the Auger tube (Auger tube LED on) starts working. They will
switch off once the period of time indicated on the display (figure 18b) has elapsed or after pressing P3 button.
figure 18°
figure 18b
11.2.8 Menu M07 – stove status
After entering menu M7 by pressing P3 button, the status of a few parameters with stove in working mode scrolls on the display. The table
below contains an example of the values scrolling on the display together with their meaning.
Displayed status meaning
3.1” Auger tube pellet feeding status
52’ Max. time for ignition phase
Toff Thermostat status
106° Fume temperature
1490 Exhaust blower speed
11.2.9 Menu M08 – technician settings
This menu item is reserved to the stove installer. After entering the password (figure 19), P1 (decrease) and P2 (increase) buttons
allow all the stove working parameters to be set.
figure 19
11.2.10 Menù M09 – exit
Select this item by pressing P3 button (figure 20) to exit the menu and go back to the previous status.
figure 20
PRE
USC
CHI
90 “
55
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.3 User functions
Standard functioning of a control board properly installed on a forced air pellet stove is described below with reference to the
functions available to users.
Before switching on the stove, the control board display is as in figure 3.
figure 3
11.3.1 Stove switching on
Hold P3 button down for a few seconds to switch on the stove. The message "Accende" (as in figure 4) appears on the display and the
ON/OFF LED starts flashing if the stove has successfully switched on. This phase lasts for the period of time set by PR0 1 parameter.
During this phase the stove goes into the pre-heating status: the ignition plug (as indicated by the relevant LED) and the exhaust blower
switch on. (figure 4)
Any problem detected during the switching-on phase is indicated on the display and the stove goes into the alarm status.
figure 4
11.3.2 Pellet feeding
The pellet feeding phase starts after approx. 1 minute: the message "Carica pellet" scrolls on the display and the ON/OFF LED starts
flashing.
During the first stage the Auger tube feeds the pellets to the burn pot during a period of time set by PR40 parameter (Auger tube
LED on), the exhaust blower speed is set by PR42 parameter and the ignition plug is still on (ignition plug LED on).
During the second stage, once the period of time set by PR40 parameter has elapsed, the Auger tube switches off (Auger tube LED
off) during a period of time set by PR4 1 parameter, while the exhaust blower speed remains as in the previous status. The ignition
plug is still on. In case of ignition failure at the end of this phase, the Auger tube switches back and remains on during the period
of time set by PR04 parameter, the exhaust blower speed is set by PR1 6 parameter and the ignition plug is still on. (figure 5)
figure 5
OFF
ACC
CAR
56
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.3.3 Fire on
Once fume temperature has reached and exceeded PR13 parameter value, the stove goes into the ignition mode: the message "Fuoco
presente" appears on the display and the ON/OFF LED starts flashing.
During this phase the temperature remains stable for a period of time preset by PR02 parameter.
The exhaust blower speed is set by PR17 parameter, the Auger tube remains on for a period of time set by PR05 parameter (Auger tube
LED flashing) and the ignition plug is off (ignition plug LED off). (figure 6)
Any problem during this phase will cause the control board to stop and the stove to go into error state.
figure 6
11.3.4 Working mode
Once fume temperature has reached and exceeded PR13 parameter value, maintaining it for the period of time set by PR02
parameter, the stove enters the normal working mode. The message "Lavoro" appears on the display and the ON/OFF LED is on.
Hold P2 button down to set the heat output and press P1 button to set the room temperature. (figure 7a)
If fume temperature reaches the threshold set by PR1 5 parameter, the air exchanger fan will switch on (as the exchanger LED).
figure 7a
During this phase, after a period of time set by PR03 parameter, the stove cleans the burn pot. The message "Pul-braciere" scrolls on the
display, the Auger tube is on (as the relevant LED) at a speed set by PR09 parameter and the exhaust blower at a speed set by PR08
parameter. (figure 7b)
Once the period of time set by PR12 parameter has elapsed, the stove goes back to the working mode.
figure 7b
11.3.5 Changing set heat output
During stove normal operation (“Lavoro” – working mode), the heat output can be changed by using P2 button (Heat output setting
LED on).
Press P2 button again to increase the heat output and P1 button to decrease it. The display will show the set heat output. (figure 8)
Do not press any button for 5 seconds or press P3 button to exit the setting mode.
figure 8
FUO
LAV
PULPot3
57
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.3.6 Changing set room temperature
Press P1 button to change the set room temperature.
The display shows the set room temperature (SET temperature value). Press P1 and P2 buttons to decrease or increase, respectively, the
temperature value. The value is saved after approx. 5 seconds and the display goes back to normal. Otherwise, press P3 to exit. (figure
9)
figure 9
11.3.7 Room temperature reaches set value (SET temperature value)
Once the set room temperature value has been reached, the stove heat output is automatically set to the minimum value. During this
phase the display shows the message "Modula". (figure 10)
If room temperature falls below the set value (Set temperature value), the stove will go back to the "Lavoro" mode and to the
previously set heat output (Set heat output value).
figure 10
11.3.8 Stand-by
When enabled in the menu, the Stand-by function allows the stove to be switched off after complying with the following conditions.
It is enabled if the room temperature exceeds the relevant set value (Set room temperature value) during the period of time set by
PR44 parameter to which PR43 parameter must be added. The message "Go-standby" appears on the display followed by the minutes
left. (figure 11a)
figure 11a
At the end of the period of time set by PR44 parameter the message "Attesa raffredda" will appear on the display. During this phase
the Auger tube is off (Auger tube LED off), the exchanger switches off once the threshold set by PR1 5 parameter has been reached and
the ON/OFF LED flashes. (figure 11b)
figure 11b
22,5c
MOD
GO-S
ATT
58
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
When fume temperature reaches the threshold set by PR13 parameter, the stove goes into the Stand-by mode and the message
"Stop eco temp good" scrolls on the display.
The Auger tube (Auger tube LED off), the exchanger (exchanger LED off) and the exhaust blower are off. (figure 11c)
figure 11c
If room temperature falls below the set value (Set room temperature value) plus the threshold set by PR43 parameter, the stove switches
back on.
11.3.9 Stove switching off
Hold P3 button down to switch off the stove. The display shows the message "Pul-Finale”. (figure 12a)
The Auger tube motor switches off (Auger tube LED off), the exhaust blower speed is set by PR08 parameter and the ON/OFF LED
flashes.
figure 12a
The exchanger blower remains on (exchanger LED on) until the fume temperature falls below the value set by PR1 5 parameter. If, at the
end of the period of time set by PR39 parameter, the fume temperature remains below the threshold set by PR1 0 parameter, the stove
will switch off and the message "Off" appears on the display. (figure 12b)
figure 12b
STO
PULOFF
59
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.4 Alarms
Should any malfunctioning be detected, the control board reports the problem in question: the alarm LED switches on (alarm LED on) and the
buzzer goes off.
The possible alarm messages are listed below:
Cause Display shows
Power outage AL 1 ALAR AL 1BLAC-OUT
Fume temperature sensor AL 2 ALAR AL2 SONDA FUMI
Fume overheating AL 3 ALAR AL3 HOT FUMI
Faulty fume encoder AL 4 ALAR AL 4 ASPIRAT-GUASTO
Ignition failure AL 5 ALAR AL 5 MANCATA ACCENSNo
pellets AL 6 ALAR AL 6 MANCANO PELLET
Thermal safety overheating AL 7 ALAR AL 7 SICUREC– TERMICA
No neg. pressure AL 8 ALAR AL 8 MANCA DEPRESSIn
case of alarm, the stove is always immediately switched off
EXCEPT FOR THE POWER OUTAGE ALARM, the alarm status is reached at the end of the period of time set by PR1 1 parameter and can be
cleared by holding P3 button down. Whenever an alarm is cleared, the stove starts a switching-off phase for safety reasons. The alarm LED
(alarm LED on) will remain on and the buzzer, if enabled, will sound intermittently during the entire alarm phase. Should the alarm not be
cleared, the stove will in any case be switched off and the alarm message will remain on the display.
11.4.1 Power outage alarm
Power outage may occur with stove in working mode. When power resumes, if the power outage period has been lower than the value
set by PR48 parameter, the stove will restart in the WORKING mode. Otherwise the relevant alarm will be triggered. The message “Al
1 alar al 1 Blac-out” (figure 21) scrolls on the display and the stove switches off.
figure 21
11.4.2 Fume temperature sensor alarm
The alarm is triggered in case of faulty fume sensor. The stove goes into the alarm status and the alarm LED switches on (alarm LED
on). The message “Al 2 alar al 2 Sonda fumi” (figure 22) will scroll on the display and the stove will switch off.
figure 22
11.4.3 Fume overheating alarm
The alarm is triggered whenever the fume sensor detects a temperature higher than a fixed set value, which may not be modified by
means of a parameter. The message “Al 3 alar al 3 Hot fumi” (figure 23) appears on the display and the stove switches off.
figure 23
AL 1
AL 2
AL 3
60
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
11.4.4 Faulty fume encoder alarm
The alarm is triggered in case of exhaust blower failure. The stove goes into the alarm status and the message “Al 4 alar al 4 Aspirat–
guasto” (figure 24) will scroll on the display.
figure 24
11.4.5 Ignition failure alarm
The alarm is triggered in case of ignition phase failure. This occurs when fume temperature does not exceed the value set by PR1 3 parameter
at the end of the period of time set by PR0 1 parameter. The message “Al 5 alar al 5 Mancata accens" scrolls on the display and the
stove goes into the alarm status (figure 25).
figure 25
11.4.6 No pellet alarm
The alarm is triggered when fume temperature falls below the value set by PR13 parameter with stove in working mode. The message
“Al 6 alar al 6 mancano pellet" scrolls on the display and the stove goes into the alarm status (figure 26).
figure 26
11.4.7 Thermal safety overheating alarm
The alarm is triggered whenever the general safety thermostat detects a temperature exceeding the trigger threshold. The thermostat
switches off the Auger tube, being connected in series to its power supply, the control board reports the alarm status (alarm LED on)
by showing the message “Al 7 alar al 7 Sicurec– termica” on the display (figure 27) and the stove switches off.
figure 27
11.4.8 No negative pressure alarm
The alarm is triggered whenever the external pressure switch detects a pressure/negative pressure value below the trigger threshold.
The pressure switch switches off the Auger tube, being connected in series to each other, and the control board reports the alarm status
(alarm LED on) by showing the message “Al 8 alar al 8 Manca depress-” on the display (figure 28). The stove switches off.
figure 28
AL 4
AL 5
AL 6
AL 7
AL 8
61
11. N100 MICRONOVA ELECTRONICS WITH 3-BUTTON LED DISPLAY
Last edit: 4 Χρόνια 9 Μήνες πριν by ΚΩΣΤΑΣ ΠΗΧΑΣ.

Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.

Περισσότερα
4 Χρόνια 9 Μήνες πριν #168161 από hellion
Απαντήθηκε από hellion στο θέμα Προβλημα με το κουμπι + σε control panel
ευχαριστω πολυ...μολις θα εχω νεωτερα θα ενημερωσω

Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.

Χρόνος δημιουργίας σελίδας: 0.103 δευτερόλεπτα
Powered by Kunena Φόρουμ